References [1] N. Sawalhi and R. B. Randall, "Simulating gear and bearing interactions in the presence of faults: Part I. The combined gear bearing dynamic model and the simulation of localised bearing faults," Mechanical Systems and Signal Processing, vol. 22, pp. 1924-1951, 2008. [2] N. Sawalhi and R. B. Randall, "Simulating gear and bearing interactions in the presence of faults: Part II: Simulation of the vibrations produced by extended bearing faults," Mechanical Systems and Signal Processing, vol. 22, pp. 1952-1966, 2008. [3] Z.-Q. Qu, Model Order Reduction Techniques :with Applications in Finite Element Analysis Springer, 2004. [4] L. I. Myklebust and B. Skallerud, "Model Reduction Methods for Flexible Structures," presented at the 15th Nordic Seminar on Computational Mechanics, Aalborg, Denmark, 2002. [5] N. Sawalhi and R. B. Randall, "A Combined Lumped Parameter and Finite Element Model of a Single Stage Gearbox for Bearing Fault Simulation," presented at the COMADEM 2008 (Condition Monitoring and Diagnostic Engineering Management), Prague, Czech Republic, 2008. [6] N. Sawalhi and R. B. Randall, "Improved Simulation of Faults in Rolling Element Bearings in Gearboxes," presented at the 9th International Conference on Vibrations in Rotating Machinery, 8-10 September, UK, 2008. [7] P. Sweeney, "Transmission error measurement and analysis " Ph. D. Dissertation, Mechanical & Manufacturing Engineering, Faculty of Engineering, University of New South Wales, Sydney, Australia, 1994. [8] S. Du, "Dynamic modelling and simulation of gear transmission error for gearbox vibration analysis," Ph.D. Dissertation, Mechanical & Manufacturing Engineering, Faculty of Engineering, University of New South Wales, Sydney, Australia, 1997. [9] H. Endo, "Simulation of gear faults and its application to the development of differential diagnostic technique " Ph. D. Dissertation, Mechanical & Manufacturing Engineering, Faculty of Engineering, University of New South Wales, Sydney, Australia, 2005. [10] J. T. Young. (2000). Primer on the Craig-Bampton Method, (Based on input from William B. Haile). [11] P. Koutsovasilis and M. Beitelschmidt, "Model order reduction of finite element models: improved component mode synthesis," Mathematical and Computer Modelling of Dynamical Systems, vol. 16:1, p. 57 — 73, 2010. [12] P. Koutsovasilis and M. Beitelschmidt, "Comparison of model reduction techniques for large mechanical systems," Multibody System Dynamics, vol. 20, pp. 111-128, 2008. [13] R. J. Guyan, "Reduction of stiffness and mass matrices," AIAA Journal, vol. 30, pp. 772-780, 1965. [14] B. M. Irons, "Structural eignvalue problems-elimination of unwanted variables," AIAA journal, vol. 3, pp. 961-962, 1965. [15] S. L. Chen and M. Géradin, "An exact model reduction procedure for mechanical systems," Computer Methods in Applied Mechanics and Engineering, vol. 143, pp. 69-78, 1997. [16] J. C. O'Callahan, "A procedure for an improved reduced system (IRS) model," in Proc. 7. International Modal Analysis Conference, Las Vegas, 1989. [17] M. I. Friswell, S. D. Garvey, and J. E. T. Penny, "Model reduction using dynamic and iterated IRS techniques," Journal of Sound and Vibration, vol. 186, pp. 311-323, 1995. [18] C. Carmignani, P. Forte, and G. Melani, "Component modal synthesis modeling of a gearbox for vibration monitoring simulation," presented at the The Sixth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, Dublin, Ireland, 2009. 409
RkJQdWJsaXNoZXIy MTMzNzEzMQ==